International Research Journal of Innovations in Engineering and Technology - IRJIET International Open Access, Monthly, Peer Reviewed, Reputed Journal ISSN (online): 2581-3048

Impact Factor (2025): 6.9

DOI Prefix: 10.47001/IRJIET

Analysis and Optimization in Electrochemical Machining by using AISI D2 Tool Steel

Deepanshu ShrivastavaResearch Scholar, Dr. C. V. Raman University Bilaspur, Chhattisgarh, IndiaShailesh DewanganAssistant Prof., Department of Production Engineering Birla Institute of Technology, Mesra, Ranchi, India

Vol 3 No 6 (2019): Volume 3, Issue 6, June 2019 | Pages: 33-36

International Research Journal of Innovations in Engineering and Technology

OPEN ACCESS | Research Article | Published Date: 04-06-2019

doi Logo

pdf iconFull Text PDF
Abstract

Electrochemical machining (ECM) is the one of the best methods for machining of AISI D2 tool steel, because it’s hard and difficulty-to-cut for any conventional machining process.  ECM has generally used in automotive, textile, die making industries medical and electronic equipment etc. During the process of machining Material Removal Rate (MRR) consider as higher the better-quality characteristics and with aim to maximize it, since it is one of the factors to be determined in the process decisions. Whereas surface roughness has been considering as the lower the better-quality characteristics with the aim to minimize it.

Keywords

Design of Experiment, Electrochemical machining (ECM), Surface Roughness, Taguchi Design, Material removal rate


Citation of this Article

Citation of this article:

Deepanshu Shrivastava, Shailesh Dewangan, “Analysis and Optimization in Electrochemical Machining by using AISI D2 Tool Steel” Published in International Research Journal of Innovations in Engineering and Technology (IRJIET), Volume 3, Issue 6, pp 33-36, June 2019.

Licence Copyright (c) 2026 International Research Journal of Innovations in Engineering and Technology creative common licence This work is licensed under Creative common Attribution Non Commercial 4.0 Internation Licence
References
  1. Chakradhar, D. and VenuGopal A. “Multi-objective optimization of electrochemical machining of EN 31 steel by grey relational analysis”,International Journal of Modeling and Optimization,vol.1, no. 2, 2011.
  2. Senthikumar, C. Ganesan, G. Karthikeyanand  R.“Study of electrochemical machining characteristics of Al/SiCp composites”,International Journal of Manufacturing Technologyvol. 43, pp. 256-263, 2009.
  3. Nayak, A.A. Gangopadhyay, S. and Sahoo, D.K. “Modelling, simulation and experimental investigation for generating ‘I’ shaped contour on Inconel 825 using electro chemical machining”,Journal of Manufacturing Processes, vol. 23, pp. 269-277, 2016.
  4. Jeykrishnan, J. Vijaya Ramnath, B. Elanchezhian, C. Akilesh, and S. Parametric “Analysis on Electro-chemical machining of SKD-12 tool steel”,Materials Today: Proceedings,vol.4, no.2,part A, pp. 3760-3766, 2017.
  5. Tiwari, A.  Mandal, A. and Kaushik K. “Multi-objective Optimization of Electro-chemical Machining by Non-dominated Sorting Genetic Algorithm”Materials Today: Proceedings, vol.2 no. (4-5), pp.  2569-2575, 2015.
  6. Mehrabi, F. Farahnakian, M. Elhami, S. and Razfar, M.R. “Application of electrolyte injection to the electro-chemical discharge machining (ECDM) on the optical glass”,Journal of Materials Processing Technology, vol. 255, pp. 665-672, 2018.
  7.  Wang, H. Zhu, D. and Liu, J. “Improving the accuracy of the blade leading/trailing edges by electrochemical machining with tangential feeding”, CIRP Annals, Under Press, 2019.
  8. Kasdekar, D.K.  Parashar, V. and Arya, C. “Artificial neural network models for the prediction of MRR in Electro-chemical machining”, Materials Today: Proceedings,vol.5 no. 1, pp. 772-779, 2018.
  9. Rahul, Datta, S. Biswal, B.B. and Mahapatra, S.S. “Machinability analysis of Inconel 601, 625, 718 and 825 during electro-discharge machining On evaluation of optimal parameters setting” Measurement, vol. 137, pp. 382-400, 2019.
  10. Dewangan S. K., Kumar P. and Jha S. K. “Optimization of Quality and Productivity of Wire EDM by using L9 Orthogonal Array”Advances in Industrial and Production Engineering, Lecture Notes in Mechanical Engineering, pp. 93-100, doi.org/10.1007/978-981-13-6412-9_9., 2019.

Copyright @ 2026 IRJIET. All Right Reserved.

Licensed underCreative Commons Attribution 4.0 International License.