International Research Journal of Innovations in Engineering and Technology - IRJIET International Open Access, Monthly, Peer Reviewed, Reputed Journal ISSN (online): 2581-3048

Impact Factor (2025): 6.9

DOI Prefix: 10.47001/IRJIET

Experimental Evaluation of the Influence of Overheating on the Properties of Metal During its Processing on Metal-cutting Machines for Subsequent use in Aeronautics

Shehret TilvaldyevAeronautics Department of Universidad Autónoma de Ciudad Juarez (UACJ), MexicoJulio César Cuéllar MataAeronautics Department of Universidad Autónoma de Ciudad Juarez (UACJ), MexicoManuel Alejandro Lira MartinezAeronautics Department of Universidad Autónoma de Ciudad Juarez (UACJ), MexicoJose Omar Davalos RamirezAeronautics Department of Universidad Autónoma de Ciudad Juarez (UACJ), Mexico

Vol 4 No 11 (2020): Volume 4, Issue 11, November 2020 | Pages: 1-10

International Research Journal of Innovations in Engineering and Technology

OPEN ACCESS | Research Article | Published Date: 10-11-2020

doi Logo doi.org/10.47001/IRJIET/2020.411001

pdf iconFull Text PDF
Abstract

Heat has critical influences on machining: it can increase tool wear and then reduce tool life, cause thermal deformation and changes to physical and mechanical properties of the job material. But due to the complexity of machining mechanics, it's hard to predict the intensity and distribution of the heat sources in an individual machining operation, and many efforts in theoretical analyses and experiments have been made to understand this phenomenon, but some problems are still unsolved. This paper reports results of Experimental researches that were performed to investigate how the heat of machining processes changes mechanical and thermal properties of the work-pieces, and how the normal and increased (overloaded) machining parameters changes heat influence and properties of material using in Aeronautics.

Keywords

Metal Cutting, Temperature in Cutting zone, Hardness property, Tensile Strength property


Citation of this Article

Shehret Tilvaldyev, Julio César Cuéllar Mata, Manuel Alejandro Lira Martinez, Jose Omar Davalos Ramirez, “Experimental Evaluation of the Influence of Overheating on the Properties of Metal During its Processing on Metal-cutting Machines for Subsequent use in Aeronautics” Published in International Research Journal of Innovations in Engineering and Technology - IRJIET, Volume 4, Issue 11, pp 1-10, November 2020. https://doi.org/10.47001/IRJIET/2020.411001

Licence Copyright (c) 2026 International Research Journal of Innovations in Engineering and Technology creative common licence This work is licensed under Creative common Attribution Non Commercial 4.0 Internation Licence
References
  1. M.C. Shaw, “Metal Cutting Principles”, Oxford University Press, New York, (1984)
  2. Ashby MF, Jones DRH (1998) “Engineering Materials 2”.  Butterworth. London.
  3. Carvalho SR, Lima e Silva SMM, Machado AR, Guimaraes G (2006) “Temperature Determination at the Chip-Tool Interface using an inverse Thermal Model Considering the Tool and the Tool Holder”. Journal of Material Processing Technology 179: 97- 104
  4. Komanduri  R and Hou Z B (2001) “Thermal modeling of the metal cutting process, Part 2: temperature rise distribution due to frictional heat source at the tool–chip interface”. Int J Mech Sci 43: 57–88
  5. Lazoglu I, Altintas Y (2002) “Prediction of tool chip temperature in continuous and interrupted machining”. Int J Mach Tools Manuf 42: 1011–1022
  6. Pavel R, Srivastava A (2007) “An experimental investigation of temperatures during conventional and CBN grinding”. Int J Adv Manuf Technol 33:412–418 
  7. Wang SB, Kou HS (2006) “Selections of working conditions for creep feed grinding. Part (II): workpiece temperature and critical grinding energy for burning”. Int J Adv Manuf Technol 28(1–2):38–44
  8. Hae-Ji Kim, Nam-Kyung Kim, Jae-Seob Kwak. “Heat flux distribution model by sequential algorithm of inverse heat transfer for determining workpiece temperature in creep feed grinding:”. International Journal of Machine Tools & Manufacture 46 (2006) 2086–2093
  9. Stephenson DA, Ali A (1992) “Tool temperatures in interrupted metal cutting, Transactions of ASME”. Journal of Engineering for Industry 114: 127–136
  10. Frederic Winslow Taylor (1907) “On the art of cutting metals”. American society of mechanical engineers.
  11. Malkin, S., “Grinding of metals: theory and application,” J, of Appl Metalwork 3:95–109, 1984.
  12. Shaw, M.C., “Grinding temperatures”, Proceedings of the 12th North American Research Conference 304-308, 1984.
  13. Pavel, R. and Srivastava, A., “An experimental investigation of temperatures during conventional and CBN grinding,” Int J Adv Manuf Technol 33:412–418, 2007.
  14.  Chandrasekar, S., Shaw, M.,C. and Bhushan, B., “Comparison of grind- ing and lapping of ferrite and metals,” Trans ASME J Eng Ind 109:76– 83, 1987.
  15. Green, D.,J., Lange, F.,F.and James, M.,R., “Factors influencing residual stresses due to  stress-induced phase transformation,” J Amer Ceram Soc 66(9):623–629, 1983.
  16.  Marshall, D.,B., Evans, A.,G., Khuri-Yakub, B.,T., Tien, J.W.  and Kino, G.,S., “The nature of machining damage in brittle materials,”  Proc Roy Soc London 385:461–475, 1983.
  17. Wang, S.,B. and Kou, H.,S., “Selections of working conditions for creep feed grinding. Part (II): workpiece temperature and critical grinding energy for burning,” Int J Adv Manuf Technol 28(1–2):38–44, 2006.
  18. King, R.,l. and Hahn, R.,S., “Modern Grinding Technology,”  Chapman and Hall, New York, London, 1986.
  19. Jaeger, J., C., “Moving Sources of Heat and the Temperature at Sliding Contacts,” Proc.R. Soc. New South Wales, 76/3: 203-224, 1942.
  20. Carslaw, H. and Jaeger, J., C., “Conduction of heat in solids”, Oxford Science Publications, Oxford University Press, 1959.
  21. Hae-Ji, Kim, Nam-Kyung Kim and Jae-Seob Kwak. “Heat flux distribution model by sequential algorithm of inverse heat transfer for determining workpiece temperature in creep feed grinding.” International Journal of Machine Tools & Manufacture 46, 2086–2093, 2006.
  22. Rowe, W.,B.,  Black, B.,  Mills, H.,S.  and Morgan, M.,N.,  “Experimental investigation of heat transfer in grinding,” Ann. CIRP 44 (1), 329–332, 1995.
  23. K.K. Hong, K.,K., and Lo, C.,Y., “An inverse analysis for the heat conduction during a grinding process,” Journal of Materials Processing Technology 105, 87-94, 2000.
  24. C. Guo, Wu,Y., Varghese,V. and Malkin.S., “Temperatures and Energy Partition for Grinding with Vitrified CBN Wheels,”  CIRP Annals - Manufacturing Technology, (48): 247-250, 1999.
  25. Malkin, S. and Guo, C., “Thermal Analysis of Grinding.” Annals of the CIRP Vol. 56/2: 760-782, 2007.
  26. Trigger, K., J., and Chao, B., T., “An Analytical Evaluation of Metal Cutting Temperatures,” Trans. ASME, 73:57-64, 1951.
  27. Malkin, S., “Thermal Aspects of Grinding Part 2 - Surface Temperatures and Workpiece Burn”, ASME Journal of Engineering for Industry, 96:184- 1191, 1974.
  28. Takazawa, K., “Effects of Grinding Variables on Surface Structure of Hardened Steels,” Bull. Japan Soc. Prec. Engg., 2:19-21, 1966.
  29. Fedoseev, O., B. and Malkin, S., “Analysis of Tempering and Rehardening for Grinding of Hardened Steels,” ASME Journal of Engineering for Industry, 113:388-394, 1991.
  30. Longbottom JM, Lanham JD (2009) “Cutting temperature measurement while machining – a review”. University of the West of England. Bristol. UK.

Copyright @ 2026 IRJIET. All Right Reserved.

Licensed underCreative Commons Attribution 4.0 International License.