International Research Journal of Innovations in Engineering and Technology - IRJIET International Open Access, Monthly, Peer Reviewed, Reputed Journal ISSN (online): 2581-3048

Impact Factor (2025): 6.9

DOI Prefix: 10.47001/IRJIET

Analysis of M-212 Conveyor Belt Modification at Raw Material Warehouse

Abstract

This study discusses the effects of the modifications to the conveyor belt on the Warehouse loading system according to CEMA standards. In this case, the specifications observed are belt width, idler selection, and material cut area. Then from the calculation of these specifications it can be calculated the performance of the conveyor belt in the form of carrying capacity, tensile force and power used on the M-212 conveyor belt in accordance with CEMA standards. The results of the analysis in this study showed that there was a reduction in the capacity of the M-212 conveyor belt after the modification. In addition, this modification also has an impact on the power required. After the modification, the required power usage is reduced from the initial 4 hp to 1.44 hp.

Country : Indonesia

1 Djoeli Satrijo2 Ojo Kurdi3 Achmad Widodo4 Muhammad Arif Rayhan

  1. Mechanical Engineering, Diponegoro University, Semarang, Indonesia
  2. Mechanical Engineering, Diponegoro University, Semarang, Indonesia
  3. Mechanical Engineering, Diponegoro University, Semarang, Indonesia
  4. Mechanical Engineering, Diponegoro University, Semarang, Indonesia

IRJIET, Volume 6, Issue 11, November 2022 pp. 112-118

doi.org/10.47001/IRJIET/2022.611015

Full Paper
Download

References

  1. P. J. U. Bugari´c, M. Tanasijevi´c, D. Polovina, D. Ignjatovi´c, “Reliability of rubber conveyor belts as a part of the overburden removal system − case study:Tamnava-East field open cast mine,” 2014.
  2. J. X. D. H. Wang, “Research on the reliability of underground coal mine belt conveyor system,” 2nd Int. Conf. Mech. Autom. Control Eng. MACE 2011 - Proc. 7636–7639, vol. MACE 2011, 2011, [Online]. Available: https://doi.org/10.1109/MACE.2011.5988818
  3. R. S. Ahmadi, S. Moosazadeh, M. Hajihassani, H. Moomivand, M.M. Rajaei, “Reliability, availability and maintainability analysis of the conveyor system in mechanized tunneling, Measurement,” 145 756–764, 2019, [Online]. Available: https://doi.org/10.1016/J.MEASUREMENT.2019.06.009
  4. J. M. X. Liu, D. He, G. Lodewijks, Y. Pang, “Integrated decision making for predictive maintenance of belt conveyor systems,” Reliab. Eng. Syst. Saf, vol. 188 (2019), 2019, [Online]. Available: https://doi.org/10.1016/J.RESS.2019.03.047
  5. C. A. ] S.N. Morales, G. A. H. an Valles, V. Torres-Argüelles, G. Erwin Martínez, and Andez, “Six Sigma improvement project in a concrete block plant,” Constr. Innov., vol. 16 (2016), [Online]. Available: https://doi.org/10.1108/CI-01-2015-0003/FULL/XML
  6. M. H. M. Bajda, “Laboratory tests of operational durability and energy-efficiency of conveyor belts,” IOP Conf. Ser. Earth Environ. Sci, vol. 261 (2019), 2019, [Online]. Available: https://doi.org/10.1088/1755-1315/261/1/012002
  7. P. Dro´zdziel A. Rudawska, R. Madlenˇak, ´ L. Madlenˇakov ´ a, “Investigation of the Effect of Operational Factors on Conveyor Belt Mechanical Properties,” Appl. Sci., vol. Vol. 10, P, 2020.
  8. T. Zur M. Hardygora, “Belt conveyors in mining,” Wydaw. „Sl ´ ąsk, 1996.
  9. M. K. G. Fedorko, V. Molnar, A. Grincova, M. Dovica, T. Toth, N. Husakova, V. Taraba, “Failure analysis of irreversible changes in the construction of rubber–textile conveyor belt damaged by sharp-edge material impact,” Eng. Fail. Anal., vol. 39 (2014), 2014, [Online]. Available: https://doi.org/10.1016/J.ENGFAILANAL.2014.01.022
  10. L. Gładysiewicz, “Belt conveyors theory and calculations,” Wroclaw Univ. Technol. Press, 2003.

Copyright @ 2026-2017 IRJIET. All Right Reserved.

Developed by Byzero Technologies