International Research Journal of Innovations in Engineering and Technology - IRJIET International Open Access, Monthly, Peer Reviewed, Reputed Journal ISSN (online): 2581-3048

Impact Factor (2025): 6.9

DOI Prefix: 10.47001/IRJIET

Investigation of Concrete to Concrete Bonding Between Different Grades Under Shear Test

Ravina G. KadekarDepartment of Civil Engineering, G.H.Raisoni University, Amravati, Maharashtra, IndiaV.M.SapateFaculty of Civil Engineering Department, G.H.Raisoni University, Amravati, Maharashtra, India

Vol 8 No 6 (2024): Volume 8, Issue 6, June 2024 | Pages: 205-207

International Research Journal of Innovations in Engineering and Technology

OPEN ACCESS | Research Article | Published Date: 29-06-2024

doi Logo doi.org/10.47001/IRJIET/2024.806026

pdf iconFull Text PDF
Abstract

The main Aim is that finding a strength of repaired bonded structure by Epoxy performing Slant Shear Test. Our structure is damaged due to some natural and manmade events after all we need to rehabilited and repaired the old structure or a damaged structure. There are many Research and study that focuses on repairing concrete structure by using epoxy based resin as a binding material. Our Focus is make use of concrete is very less and instead of these we use a binding material that is Epoxy resin to make a construction faster and easier and having a strength as like as concrete mix. The slant shear test strength is conducted for block of repaired concrete are based on concrete grade of substrate and thickness of epoxy. Casting of different grades of cylindrical slants and cured up to 28 days. After that taking these cylindrical slants and bonded them with epoxy using different thickness and test using specification of ASTM C882. It is observed that increase in thickness the strength of concrete is also increase and also observed that failure of bonding is occur when two substrate of different material is bonded and fails the substrate whichever is low grade.  

Keywords

Concrete, Rehabilitation, Epoxy Resin, Slant Shear Test, Grades of Concete, Concrete Block, Bond Failure, Cylindrical Slant


Citation of this Article:

Ravina G. Kadekar, & V.M.Sapate. (2024). Investigation of Concrete to Concrete Bonding Between Different Grades Under Shear Test. International Research Journal of Innovations in Engineering and Technology - IRJIET, 8(6), 205-207. Article DOI https://doi.org/10.47001/IRJIET/2024.806026

Licence Copyright (c) 2026 International Research Journal of Innovations in Engineering and Technology creative common licence This work is licensed under Creative common Attribution Non Commercial 4.0 Internation Licence
References
  1. Wall et.al, J. S., N. G. Shrive, and B. R. Gamble 1986 Testing of bond between fresh and hardened concrete. In Adhesion between polymers and concrete/Adhésion entre polymères et béton, pp. 335-344. Springer, Boston.
  2. Santos, E.N.B.S. Júlio, V.D. Silva, Correlation between concrete-to-concrete bond strength and the roughness of the substrate surface, Constr. Build. Mater. 21 (2007) 1688–1695, https://doi.org/10.1016/j. conbuildmat.2006.05.044.
  3. Rashmi R.Pattnaik (2015) ‘Investigation on ASTM C882 Test Procedure of Slant Shear Bond Strength of Concrete Repair Material’, International Journal of Civil, Structural, Engineering,05(02) Chalermek.
  4. Issa, C.A., & Deps, P.(2007). Experimental study of epoxy repairing in cracks in concrete. Construction and Building Materials, 21(1), 157-163.
  5. Dawood and Ganim (2017) ‘Effective Performance Mortar Reinforced with Fibres as Repair Material’, Challenge Journal of Concrete Research Letters, 08(02), pp.29-47.
  6. Arezoumandi, M., Wolfe, M.H., Volz, J.S., 2013. A comparative study of the bond strength of reinforcing steel in high-volume fly ash concrete and conventional concrete. Constr. Build. Mater. 40, 919e924.
  7. Júlio, E. N. B., Branco, F. A., & Silva, V. D. (2004). ‘Concrete-to-concrete bond strength. Influence of the roughness of the substrate surface’, Construction and Building Materials, 18(9), pp 675–681.
  8. Bilek, V., Bonczková, S., Hurta, J., Pytlík, D., & Mrovec, M.,(2017). ‘Bond Strength between Reinforcing Steel and Different Types of Concrete’, Procedia Engineering, Structural and Physical Aspects of Construction Engineering, pp 243-247.
  9. Austin, S., Robins, P., & Pan, Y. (1999). ‘Shear bond testing of concrete repairs’. Cement and Concrete Research, 29(7), pp 1067–1076.
  10. ASTM C 109 “Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)”.
  11. IS code 10262:2019 “concrete mix proportioning-guidelines”.
  12. IS code 456:2000 “plain and reinforced concrete (fourth revision)”.
  13. Director general works {DG(W)},”Central Public Works Department (CPWD)”- Government of India, New Delhi.
  14. Is code 383:2016 “Coarse and Fine Aggregate for Concrete-specification” Bureau of Indian Standards. New Delhi, India.

Copyright @ 2026 IRJIET. All Right Reserved.

Licensed underCreative Commons Attribution 4.0 International License.