International Research Journal of Innovations in Engineering and Technology - IRJIET International Open Access, Monthly, Peer Reviewed, Reputed Journal ISSN (online): 2581-3048

Impact Factor (2025): 6.9

DOI Prefix: 10.47001/IRJIET

Influence of B₄C, Gr, and ZrO₂ Reinforcement Additions on the Mechanical Properties of Al-7075 Composites

Sampath Kumar RSelection Grade-1 Lecturer, Mechanical Engineering Department, Government Polytechnic Hosadurga-577527, Karnataka, India & Department of Mechanical Engineering, University Visvesvaraya College of Engineering, Bangalore University, Bangalore-560001, KarnatH C ChittappaDepartment of Mechanical Engineering, University Visvesvaraya College of Engineering, Bangalore University, Bangalore-560001, Karnataka, India

Vol 9 No 12 (2025): Volume 9, Issue 12, December 2025 | Pages: 167-179

International Research Journal of Innovations in Engineering and Technology

OPEN ACCESS | Research Article | Published Date: 27-12-2025

doi Logo doi.org/10.47001/IRJIET/2025.912026

pdf iconFull Text PDF
Abstract

This study examines the effect of 3 wt.% additions of boron carbide (B₄C), graphite (Gr), and zirconia (ZrO₂) on the mechanical performance of Al-7075 metal matrix composites fabricated through a two-step stir-casting method. Three individual composite systemsAl7075+3wt.%B₄C, Al7075+3wt.% Gr, and Al7075+3wt.%ZrO₂ were produced to evaluate the distinct strengthening mechanisms associated with each reinforcement. Microstructural characterization using Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) confirmed uniform particle distribution and sound interfacial bonding within the composites. The fabricated samples were subjected to tensile, compressive, hardness, impact, and flexural tests to compare their mechanical responses. The results showed that the B₄C-reinforced composite achieved the highest ultimate tensile strength of 245 MPa, indicating superior load-carrying capability. The graphite-reinforced composite exhibited the greatest improvement in toughness, showing an 11.5% increase in impact strength due to the crack-arresting and solid-lubricating characteristics of Gr particles. B₄C addition further enhanced compressive and flexural behaviour, achieving a maximum compressive strength of 649 MPa and a 15.9% improvement in flexural strength, attributed to refined microstructure and efficient stress transfer from the matrix to hard ceramic particles. The novelty of this work lies in directly comparing B₄C, Gr, and ZrO₂ reinforcements at the same 3 wt.% level, allowing clear identification of their individual effects on Al-7075. The findings support the selection of suitable reinforcements for aerospace, automotive, defence, and other lightweight load-bearing applications.

Keywords

Al-7075, Metal Matrix Composite, Boron Carbide, Graphite, Zirconia, Mechanical Properties, Stir Casting, Microstructure


Citation of this Article

Sampath Kumar R, & H C Chittappa. (2025). Influence of B?C, Gr, and ZrO? Reinforcement Additions on the Mechanical Properties of Al-7075 Composites. International Research Journal of Innovations in Engineering and Technology - IRJIET, 9(12), 167-179. Article DOI https://doi.org/10.47001/IRJIET/2025.912026

Licence Copyright (c) 2026 International Research Journal of Innovations in Engineering and Technology creative common licence This work is licensed under Creative common Attribution Non Commercial 4.0 Internation Licence
References
  1. Ravikumar, M., Rudra, N., Vinod, B.R., Chethana, K.Y. and Rammohan, Y.S. (2023). Study on nanosized Al2O3 and Al2O3-SiC on mechanical, wear and fracture surface of Al7075 composites for soil anchoring applications, Materials Physics and Mechanics, 51, pp. 1-18. DOI: https://doi.org/10.18149/MPM.51x2023_x.
  2. E.A. Shalaby, A.Y. Churyumov, A.N. Solonin, A. Lotfy, Preparation and characterization of hybrid A359/ (SiC+Si3N4) composites synthesized by stir/squeeze casting techniques, Mater. Sci. Eng., A 674 (2016) 18–24.
  3. U.K. Annigeri, G.B. Veeresh Kumar, Method of stir casting of aluminium metal matrix composites: a review, Elsevier’s Mater. Today: Proc. 4 (2) (2017) 1140–1146. Part A.
  4. G.B. Veeresh Kumar, C.S.P. Rao, N. Selvaraj, Studies on mechanical and dry sliding wear of Al6061–SiC composites, Composites. B 43 (3) (2012) 1185–1191.
  5. Krishna Dama, L Prashanth, Madeva Nagaral, Rakesh Mathapati, MB Hanumantharayagouda. Microstructure and mechanical behavior of B4C particulates reinforced ZA27 alloy composites. Materials Today: Proceedings, 4, 8, 2017, pp. 7546-7553.
  6. V Bharath, V Auradi, Madeva Nagaral, Satish Babu Bopanna. Influence of alumina percentage on microstructure, mechanical and wear behavior of 2014 aluminium alumina metal matrix composites. Jurnal Tribologi, 25, 1, 2020, pp. 29-44.
  7. Raj, K., Deshpande,R.G., Gopinath, B., Jayasheel, H., Nagaral, M., Auradi, V., 2021. Mechanical Fractography and Worn Surface Analysis of Nanographite and ZrO2-Reinforced Al7075 Alloy Aerospace Metal Composites, Journal of Failure Analysis and Prevention, 21, pp. 525-536.
  8. Bharath, V., Santhrusht, S.A., Nagaral, M., Auradi, V., Kori, S.A., 2019. Characterization and Mechanical Properties of 2014 Aluminum Alloy Reinforced with Al2O3p Composite Produced by Two-Stage StirCasting Route. Journal of the Institution of Engineers (India): Series C, 100, pp. 277-282.
  9. Madeva Nagaral, BK Shivananda, V Auradi, SA Kori. Effect of SiC and graphite particulates addition on wear behaviour of Al2219 alloy hybrid composites. IOP Conference Series: Materials Science and Engineering, 149, 1, 2016, 012108.
  10. Zeeshan Ali, V Muthuraman, P Rathnakumar, P Gurusamy, Madeva Nagaral. Influence of B4C particle size on the mechanical behavior of A356 aluminium composites. Research on Engineering Structures and Materials, 9, 2, 2023, pp. 527-540.
  11. V Venkataraman, Madeva Nagaral. Mechanical characterization and wear behavior of aerospace alloy AA2124 and micro B4C reinforced metal composites. Journal of Metals, Materials and Minerals, 30, 4, 2020, pp. 97-105.
  12. TH Manjunatha, Yadavalli Basavaraj, Madeva Nagaral, V Venkataramana, Jayasheel I Harti. Investigations on mechanical behavior of Al7075-nano B4C composites. IOP Conference Series: Materials Science and Engineering, 376, 1, 2018, pp. 012091.
  13. Thomas AT, Parameshwaran R, Muthukrishnan A, Kumaran MA. Development of feeding & stirring mechanisms for stir casting of aluminium matrix composites. Procedia Mater. Sci. 2014; 5: 1182e91. https://doi.org/10.1016/j.mspro.2014.07.415.
  14. Sajjadi SA, Torabi Parizi M, Ezatpour HR, Sedghi A. Fabrication of A356 composite reinforced with micro and nano Al2O3 particles by a developed composting method andstudy of its properties. J Alloys Compd 2012; 511:226e31. https://doi.org/10.1016/j.jallcom.2011.08.105.
  15. Raj R, Thakur DG. Qualitative and quantitative assessment of microstructure in Al-B4C metal matrix composite processed by modified stir casting technique. Arch. Civ. Mech. Eng. 2016;16:949e60. https://doi.org/10.1016/j.acme.2016.07.004.
  16. Kumar, V.A., Anil, M.P., Rajesh, G.L., Hiremath, V. and Auradi, V., 2018. Tensile and compression behaviour of boron carbide reinforced 6061Al MMC’s processed through conventional melt stirring. Materials Today Proceedings, 5, pp. 16141–16145.
  17. Hamid Reza Ezatpour, S.A. Sajjadi, Mohsen Haddad Sabzevar, Yizhong Huang, Investigation of microstructure and mechanical properties of Al6061 nanocomposite fabricated by stir casting, Mater. Des. 55 (2014) 921–928.
  18. Mohsen Hossein Zadeh, Omid Mirzaee, Peyman Saidi, Structural and mechanical characterization of Al based reinforced with heat treated Al2O3 particles, Mater. Des. 54 (2014) 245–250.
  19. Baradeswaran A, Perumal AE. (2013) “Influence of B4C on the tribological and mechanical properties of Al7075–B4C composites”. Composites Part B: Engineering. Volume 54, pp. 146-52.
  20. Kumar R, Dhiman S. (2013)“A study of sliding wear behaviors of Al-7075 alloy and Al-7075 hybrid composite by response surface methodology analysis”. Materials & Design. Volume 50, pp. 351-9.
  21. Nagaral M, Auradi V, Kori SA (2014) Dry sliding wear behaviour of graphite particulate reinforced Al6061 alloy composite materials 170-174; 592-594.
  22. M. Nagaral, R.G. Deshapande, V. Auradi, S.B. Boppana, S. Dayanand, M.R. Anilkumar, Mechanical and wear characterization of ceramic boron carbide-reinforced Al2024 alloy metal composites, J. Bio- Tribo-Corros. 7 (2021) 1–12.
  23. Standard Test Methods for Tension Testing of Metallic Materials, ASTM E8, 10.1520/E0008_E0008M-22.
  24. Nagaral, M., Shivananda, B. K., Auradi, V., & Kori, S. A. (2016, September). Effect of SiC and graphite particulates addition on wear behaviour of Al2219 alloy hybrid composites. In IOP Conference Series: Materials Science and Engineering (Vol. 149, No. 1, p. 012108). IOP Publishing.
  25. Kotresha Mydur, Mahendra Kumar S., Madeva Nagaral et al., “Microstructure, physical, tensile and wear behaviour of B4C particles reinforced Al7010 alloy composites” Manufacturing Rev. 10, 3 (2023).
  26. Rashmi P Shetty, T Hemanth Raju, Madeva Nagaral, Nithin Kumar, V Auradi. Effect of B4C Particles Addition on the Mechanical, Tensile Fracture and Wear Behavior of Al7075 Alloy Composites. Journal of Bio-and Tribo-Corrosion, 10, 2, 2024, 32.

Copyright @ 2026 IRJIET. All Right Reserved.

Licensed underCreative Commons Attribution 4.0 International License.